I purchased their n300 wireless USB adapter (802.11n) and installed it for one of my customers. It wasn’t as easy to install as most Mac users would like, but it wasn’t too terribly hard. The package included a CD and good, step-by-step instructions. Once installed, I could see and connect to wireless networks that were outside the range of other wireless Macs or PCs in the same offices. That was impressive. I connected to the wireless router and confirmed that the computer could connect to the Internet. Then I shut the computer down and restarted to make sure all my changes were saved. ![]() This computer had been in service for several years already and had a significant amount of corruption in the file system. When I turned the power back on, the system didn’t detect the adapter plugged into the USB port. I had to reinsert it before it would work again. This is actually something different. The USB card you have is a older 802.11g. They may have decided to only support 802.11n cards. This is not a mac address thing it is the type of radio chip. Question: Q: Belkin G Wireless USB Adapter for Mac OS X Panther 10.3 v.5000 More Less Apple Footer This site contains user submitted content, comments and opinions and is for informational purposes only. Restarting the system without powering down didn’t have the same problem. AftertheMac’s tech support people recommended repairing disk permissions and running some other routine cleanup utilities. I tried two different utilities before their tech suggested I try OnyX. I installed that and ran the cleaning utility as well as a few others to clear application and system caches and repair disk permissions again. That time it worked! The only real drawback to this adapter was the tech support. AftertheMac is a small company with limited resources. Nine times out of ten, their 800 number rang to an answering machine, and it usually took a day or more for anyone to call me back. Once I had them on the phone, they were always very helpful and seemed to know what they were doing. Is compatible with OS X 10.3+ and will connect to 802.11b, g, or n routers. You can see more information at their. If you’ve used this adapter (or another after-market Mac accessory), let me know in the comments. I’m curious about your experience with it. Adobe flash player for mac install problems. I have a D-Link wireless router and USB dongle package, it works with my windows laptops perfectly well. I am looking for a way to use the USB wireless dongle with a G5 tower so I can use the Mac as a web machine. There is a software driver for the dongle but I have no idea what information on the different tabs I should enter, so any ideas what this should be? The user manual is for windows, there is information on how to set up for Mac, despite the inclusion of the Mac driver on the CD. The dongle is a D-Link DWA-111, user manual here: thanks for any help. Hi BD Very good of you to reply So, the SW is already installed & you went to Network>Show:>Network Port Configurations & got the pop-up about a new Port detected? The driver is installed using a D-Link installer, it creates an entry in: system settings > other: its called D-Link DWA-111 I don't get a popup about a new port when opening up the D_Link icon I get: I have no idea what to do next Is that Interface dragged to the top of Network>Show:>Network Port Configurations and checked ON? Do the tabs you're talking about look like this? Nope, I only get the D_Link window From your suggested way above; how do I get this software and I can try setting up the USB with this? Many thanks for your help. I use a d-link dwl g122 dongle that has the same RT73 ralink chip. The d-link driver that came with the CD just did one thing to my G5 powermac: kernelpanic! After some searching on the web i found out, that it is best not to use the d-link driver at all, but to use the original ralink driver for the chip provided here: load the 'USB(RT257X/RT2671/RT2500)' driver. That's the driver, that will give you the wireless utility as it is shown in BD's picture. Before you install it, make sure that you uninstall the d-link driver completely. There should be an uninstaller in the dmg or zip file, that was on the CD. Then install the ralink driver and after that connect your d-link dongle. The wireless utility should pop up after a minute or so, but first you've to go to the network preference pane and confirm, that there is a new port detected. Netflix for macbook. Then you can go back to the wireless utility, that by then should be searching for available wireless networks in the site survey tab. Choose yours and enter the password when asked. After that safe the connection to a profile. Message was edited by: dirkt68. Thanks to you both none of your suggestions worked no wireless config window appears network preferences doesn't show any RALINK or D-Link stuff its too difficult to bother with, tried for 7 months to get it to work so I threw it in the bin A friend gave me a USB called Addon and I was connected in 5 minutes Its really pathetic there are no user guides for many of the Mac software supplied by 3rd party manufacturers for hardware such as printers, USB kit and still cameras. There was a 55 page manual for Windows machines and not one mention of Mac despite the D-Link driver on the CD. Drum kit app for mac.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |